Determination of 15 phthalate esters in air by gas-phase and particle-phase simultaneous sampling

Based on previous research, the sampling and analysis methods for phthalate esters (PAEs) were improved by increasing the sampling flow of indoor air from 1 to 4 L/min, shortening the sampling duration from 8 to 2 hr. Meanwhile, through the optimization of chromatographic conditions, the concentrations of 9 additional PAE pollutants in indoor air were measured. The optimized chromatographic conditions required a similar amount of time for analysis as before, but gave high responsivity, the capability of simultaneously distinguishing 15 kinds of PAEs, and a high level of discrimination between individual sample peaks, as well as stable peak generation. The recovery rate of all gas-phase and particle-phase samples of the 15 kinds of PAEs ranged from 91.26% to 109.42%, meeting the quantitative analysis requirements for indoor and outdoor air sampling and analysis. For the first time, investigation of the concentration levels as well as characteristics of 15 kinds of PAEs in the indoor air from four different traffic micro-environments (private vehicles, busses, taxis and subways) was carried out, along with validation of the optimized sampling and analytical method. The results show that all the 9 additional PAEs could be detected at relatively high pollution levels in the indoor air from the four traffic micro-environments. As none of the pollution levels of the 15 kinds of PAEs in the indoor air from the 4 traffic micro-environments should be neglected, it is of great significance to increase the types of PAEs able to be detected in indoor air.     

Effect of lubricant sulfur on the morphology and elemental composition of diesel exhaust particles

This work investigates the effects of lubricant sulfur contents on the morphology, nanostructure, size distribution and elemental composition of diesel exhaust particle on a light-duty diesel engine. Three kinds of lubricant (LS-oil, MS-oil and HS-oil, all of which have different sulfur contents: 0.182%, 0.583% and 1.06%, respectively) were used in this study. The morphologies and nanostructures of exhaust particles were analyzed using high-resolution transmission electron microscopy (TEM). Size distributions of primary particles were determined through advanced image-processing software. Elemental compositions of exhaust particles were obtained through X-ray energy dispersive spectroscopy (EDS). Results show that as lubricant sulfur contents increase, the macroscopic structure of diesel exhaust particles turn from chain-like to a more complex agglomerate. The inner cores of the core-shell structure belonging to these primary particles change little; the shell thickness decreases, and the spacing of carbon layer gradually descends, and amorphous materials that attached onto outer carbon layer of primary particles increase. Size distributions of primary particles present a unimodal and normal distribution, and higher sulfur contents lead to larger size primary particles. The sulfur content in lubricants directly affects the chemical composition in the particles. The content of C (carbon) decreases as sulfur increases in the lubricants, while the contents of O (oxygen), S (sulfur) and trace elements (including S, Si (silicon), Fe (ferrum), P (phosphorus), Ca (calcium), Zn (zinc), Mg (magnesium), Cl (chlorine) and Ni (nickel)) all increase in particles.     

关于渗透通风条件建筑结构对室内PM2.5浓度水平影响评价模型探讨

我国京津冀地区近年频遭大气PM_2.5污染侵扰,相关研究表明,既使关闭建筑外窗,大气中PM_2.5仍可以通过渗透通风方式进入室内污染环境.为定量评价建筑渗透通风及无室内污染源条件下建筑结构（如外窗缝隙结构、房间建筑结构等）对室内ρ（PM_2.5）的影响规律,基于北京市东城区、朝阳区6个不同建筑结构的房间室内外ρ（PM_2.5）实时监测数据,重点比较分析了建筑结构对室内外ρ（PM_2.5）关联特性的影响规律.此外,根据颗粒物穿透特性及沉降特性机理,提出了反映建筑外窗缝隙结构（如缝高、缝深）的无量纲特征参数A_P与反映房间建筑结构（如层高、开间、进深）的无量纲特征参数A_k.在前期提出的室内ρ（PM_2.5）预测模型基础上,进一步构建了二者（A_P与A_k）对室内ρ（PM_2.5）影响的评价模型,并通过实测数据验证了模型的正确性.结果表明:当室外PM_2.5污染程度与气象条件一定时,建筑结构对I/O[室内外ρ（PM_2.5）之比]影响较大,其范围在0.4~0.7之间;随着建筑外窗气密性等级的提高,对应室内ρ（PM_2.5）呈显著的下降趋势.建筑外窗缝隙结构对室内ρ（PM_2.5）影响程度远大于房间建筑结构,敏感性分析结果表明,当建筑外窗缝高每降低50%或缝深每提高50%,对应室内ρ（PM_2.5）约可下降33.6%与31.9%.研究显示,气密性等级较高的建筑外窗缝隙缝高往往较小、缝深较长,渗透通风条件下对控制室内ρ（PM_2.5）水平作用更显著。      

基于GeoDA的江苏省长江总磷空间关联度分析研究

利用地理空间分析方法和空间分析软件,采用2006年-2015年江苏省长江10个干流和45个入江支流监测点位的总磷浓度数据的年平均值,分析了江苏省长江干流和支流总磷浓度的空间相关性及其时空演变特征.分析发现长江总磷污染呈现全局正相关,相关指数总体呈现先减小后增加的趋势,直至2015年增至最大,干流总磷污染的重心先向西北后向西南移动,支流总磷污染的重心先向西北再向东南移动,重心移动幅度不大,并且二者均有向北面移动的趋势,同时移动幅度接近,长江干流总磷污染与支流的汇入是密不可分的.     

环境资源禀赋视角下产业升级路径研究——以浙江为例

本研究以浙江省为例,立足环境资源禀赋的优势和不足,进行产业发展现状和环境资源禀赋的相容性分析,剖析产业发展存在的问题,探索新时期环境资源禀赋支撑产业升级的路径与模式,提出浙江省基于环境资源禀赋的产业发展原则和思路,要支持发展符合环境资源条件和顺应产业发展规律的优质产业,限制发展不符合环境资源条件的低端产业,建议重点发展知识技术密集型产业、海洋经济和临港产业、生态休闲养生产业、现代大农业,并积极推进传统产业转型发展.     

石墨烯是促进还是抑制嗜酸性氧化亚铁硫杆菌生长?

尽管石墨烯以其独特的光学、电学、力学特性在各大领域都具有广阔的应用前景,但其工业化使用后在环境当中的行为,特别是遗留下的石墨烯对生态系统的毒性研究则鲜见报道.因此,本文以嗜酸性氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans)为目标微生物,探讨不同浓度(1、10、50 mg·L-1)石墨烯对Acidithiobacillus ferrooxidans的毒性效应.结果表明,石墨烯对Acidithiobacillus ferrooxidans的生长有明显抑制作用,且抑制作用随着石墨烯浓度的降低而增强.在石墨烯投加量为1 mg·L-1时,培养48 h后菌株的生长量OD420达到最大值0.045,低于空白组的0.163;并且其可溶性蛋白含量也达到最大值1.546 mg·L-1,低于空白组的3.789 mg·L-1.不同浓度石墨烯对体系p H和ORP均存在不同程度的影响,低浓度下的石墨烯影响最为显著.此外,通过扫描电镜(SEM)和荧光显微镜分析,进一步证实Acidithiobacillus ferrooxidans能在高浓度的石墨烯上生长,而低浓度的石墨烯则会对细胞膜造成损伤,它极其尖锐的边缘是细菌失活的有效机制.因此,石墨烯的毒性具有剂量效应,这一结果可为石墨烯合理利用及评价其生态毒性提供理论依据.     

我国生物质气化发电行业综合风险评价

针对我国生物质气化发电行业的现状,总结诸多风险的影响因素,建立了我国生物质气化发电行业综合风险评价体系。该评价体系主要包括5个一级风险影响因素:市场风险、技术风险、安全风险、管理风险、环境风险,每个一级影响因素包括4个二级风险影响因素。由层次分析法获得各个一级影响因素和二级影响因素的权重值,根据所构建的评价集和评分标准,结合模糊综合评价法对我国生物质气化发电行业现状的综合风险等级做定量定性分析。综合风险评价研究结果表明,生物质气化发电行业处于"较高"的风险等级,与实际情况相符。综合风险评价体系的构建合理,所建立的评价方法以及相应对策分析可为决策者提供参考依据。     

Pollution levels and characteristics of phthalate esters in indoor air of offices

The pollution status and characteristics of PAEs (phthalate esters) were investigated in indoor air of offices, and PAEs of both gas-phase and particulate-phase were detected in all the samples. The concentration (sum of the gas phase and the particulate phase) was 4748.24 ng/m³, ranging between 3070.09 and 6700.14 ng/m³. Diethyl phthalate, dibutyl phthalate, and di(2-ethylhexyl) phthalate were the most abundant compounds, together accounting for 70% of the Σ6PAEs. Dividing the particulate-phase PAEs into four size ranges (<2.5, 2.5-5, 5-10, >10 μm), the result indicated that PAEs in PM_2.5 were the most abundant, with the proportion of 72.64%. In addition, the PAE concentration in PM_2.5 correlated significantly with the total particulate-phase PAEs (R² = 0.85). Thus, the amount of PAEs in PM_2.5 can be estimated from the total amount of particulate-phase PAEs using this proportion. In a comparison between the offices and a newly decorated study room, it was found that pollution characteristics were similar between these two places. Thus, it is implied that the PAE concentration decreased by 50% 2 yr after decorating.     

Microcystis aeruginosa/Pseudomonas pseudoalcaligenes interaction effects on off-flavors in algae/bacteria co-culture system under different temperatures

We conducted an experiment to study the interaction effects of Microcystis aeruginosa and Pseudomonas pseudoalcaligenes on off-flavors in an algae/bacteria co-culture system at three temperatures (24, 28 and 32°C). Gas chromatography–mass spectrometry was applied to measure off-flavor compounds dimethyl sulfide (DMS), dimethyl trisulfide (DMTS), 2-methylisoborneol, geosmin (GEO) and β-cyclocitral. During the lag phase of co-cultured M. aeruginosa (first 15 days), P. pseudoalcaligenes significantly increased the production of DMS, DMTS and β-cyclocitral at all three temperatures. In the exponential phase of co-cultured M. aeruginosa (after 15 days), M. aeruginosa became the main factor on off-flavors in the co-culture system, and β-cyclocitral turned to the highest off-flavor compound. These results also indicated that DMS, DMTS and β-cyclocitral were the main off-flavor compounds in our M. aeruginosa/P. pseudoalcaligenes co-culture system. Univariate analysis was applied to investigate the effects of M. aeruginosa and P. pseudoalcaligenes on the production of off-flavors. The results demonstrated that both M. aeruginosa and P. pseudoalcaligenes could increase the production of DMS and DMTS, while β-cyclocitral was mainly determined by M. aeruginosa. Our results also provide some insights into understanding the relationship between cyanobacteria and heterotrophic bacteria.     

Microcystis aeruginosa/Pseudomonas pseudoalcaligenes interaction effects on off-flavors in algae/bacteria co-culture system under different temperatures

We conducted an experiment to study the interaction effects of Microcystis aeruginosa and Pseudomonas pseudoalcaligenes on off-flavors in an algae/bacteria co-culture system at three temperatures(24, 28 and 32℃). Gas chromatography–mass spectrometry was applied to measure off-flavor compounds dimethyl sulfide(DMS), dimethyl trisulfide(DMTS),2-methylisoborneol, geosmin(GEO) and β-cyclocitral. During the lag phase of co-cultured M. aeruginosa(first 15 days), P. pseudoalcaligenes significantly increased the production of DMS, DMTS and β-cyclocitral at all three temperatures. In the exponential phase of co-cultured M. aeruginosa(after 15 days), M. aeruginosa became the main factor on off-flavors in the co-culture system, and β-cyclocitral turned to the highest off-flavor compound. These results also indicated that DMS, DMTS and β-cyclocitral were the main off-flavor compounds in our M. aeruginosa/P. pseudoalcaligenes co-culture system. Univariate analysis was applied to investigate the effects of M. aeruginosa and P. pseudoalcaligenes on the production of off-flavors. The results demonstrated that both M. aeruginosa and P. pseudoalcaligenes could increase the production of DMS and DMTS, while β-cyclocitral was mainly determined by M. aeruginosa. Our results also provide some insights into understanding the relationship between cyanobacteria and heterotrophic bacteria.